PocketWizard MiniTT1 Transmitter for Canon DSLR
The smallest PocketWizard radio ever, the MiniTT1 Transmitter locks onto the cameras hot shoe supporting an on-camera flash with its own hot shoe while working with remote PocketWizard units. Remotes can be one or more PocketWizard FlexTT5 Transceivers connected to Canon E-TTL II flashes or any PocketWizard Receiver for triggering flash or remote cameras.
The MiniTT1 Transmitter is easy to use; just slide in place and begin to shoot. The new PocketWizard ControlTL System interprets the complex E-TTL II data being sent through the cameras hot shoe and digitally transmits it in a reliable radio signal. Change the flash compensation dial on the camera, and those commands pass seamlessly through the system to your remote flash. Adjust your shutter speed, aperture or ISO and the system corrects for those changes. A ratio command set on the flash or command unit passes through the MiniTT1 to set the remotes. PocketWizard ControlTL radio communication allows you to shoot farther, faster, around corners, through walls even at high noon in bright daylight. Now you can deploy a wireless flash system wherever you want, without infrared limitations, in seconds.
Use the MiniTT1 for standard triggering with any PocketWizard Receiver including the FlexTT5, PlusII or MultiMAX. When used this way with a digital camera, you can take advantage of PocketWizards HyperSync Technology that allows up to 1/500th of a second camera sync with many camera/strobe set-ups. HyperSync allows you to advance the timing of your flash trigger so that faster than X-sync speeds can be achieved.
Need more speed? Push your ControlTL system beyond 1/500th and go into FP/High-Speed sync mode automatically. No buttons to press or settings to change other than your shutter speed will give you flash sync all the way to 1/8000th.
A new PocketWizard Utility program is provided to support the MiniTT1 via a USB port. The Utility allows you to configure your channel settings, dial in your HyperSync timing, adjust your sleep-mode timers and update your product to the latest firmware.
The PocketWizard MiniTT1 Transmitter is the start of a new era in wireless trigger control."
Canon E-TTL II
FCC/IC: 340.00-354.00 MHz North America
CE model: 433.42-434.42 MHz EU/Asia/Other
52 Channels over 26 Frequencies (FCC/IC)
35 Channels over 5 Frequencies (CE)
Transmit output power:
Less than 0.001 watt (1/1000 of a watt or 1 milliwatt)
30 to 800 feet (10 to 240 meters) for E-TTL II triggering depending on flash used, antenna orientation and other variables.
30 to 1200 feet (10 to 365 meters) for basic triggering depending on flash used, antenna orientation and other variables.
For more info, click here.
Maximum Shooting Rate: Frames per Second (fps)
8 fps for E-TTL II & normal triggering
Power / Channel Switch:
OFF - C.2 - C.1
LED, Green, Amber, Red status indications
3.3 VDC (all pins) - safe for all cameras
Hot Shoe voltage protection
Hot Shoe: up to 50V
USB Compliant 2.0, Mini-B Connector
above -15C (5 F) and below 50 C (120 F)
above -30 C (-22 F) and below 85 C (185 F)
High impact plastic, captive battery door
Hot shoe made of glass reinforced resin
3 V Lithium battery, CR2450 (included) or CR2354 Lithium coin cell type
Hundreds of hours of camera "awake time" depending on shooting habits
2.8" (7.1 cm) long x 1.9" (4.9 cm) wide x 1.3" (3.3 cm) tall
2.3 oz (65 grams), 2.0 oz (57 grams) without battery
Included in the box:
MiniTT1 Transmitter, USB cable, CR2450 battery, Quick Guide
Length: 5.3 inches (13.46 cm)
Width: 5.3 inches (13.46 cm)
Height: 2 inches (5.08 cm)